Wednesday, August 3, 2022

Barrage 2022: Part II: Skiff #1 with Heroes

 I almost had the second skiff painted when I made the first posting about this game, so all I had to do really was paint the figures.  This is the skiff that has some henchman as well as the heroes minus Leia and the droids on it.  

This skiff is exactly like the first one EXCEPT that I added a thin piece of foam on the bottom in the shape of a staple that once glued to the bottom side of the skiff allows me to slide the "plank" in and have it extend off the side of the skiff.  Since I'm not really sure how I'm going to start the game (Luke on the plank or already off the plank?) I needed to have the plank on the skiff regardless of where Luke starts the game, so I knew I was going to have to figure out a way to mount it.  However, I didn't want it to be permanently attached just so that I can have more flexibility with the skiffs and, like the tail fins, if I mounted the plank permanent I'm sure it would break off during transit.  As is usual when I do something a second or third time, I think I did a better job painting this second skiff than the first having had one "under my belt" already and I could avoid some of the mistakes I made.


I took some close ups of the figures this time as well, so I will talk about them later with their pictures.  But as you can see, this skiff has a plank for Luke.  Again, it's removable.  In all other ways, this is identical to the other skiff.  I used the same templates to cut the pieces of both of the skiffs so they share the same dimensions.  If you are interested, they are about 11.5" long and 5" wide at their widest point.



I really like how the figures came out.  Here are some heroes.


Han and Chewie obviously.  Both came out better than I thought they would.  I was able to pitch Han forward a bit so he is "leaning into" his shot.  His shirt has a flap on the front that is opened and I just constructed the flap with paper.  In all other ways he's standard milk bottle figure construction including the big bangs that I like to put on my figures, and in this case they are appropriate for Captain Solo.  Chewie was tough at first, how to make him tall without being too tall, and he had to be relatively thin.  He's a milk bottle with a barrel bead sideways glued on top, then with the standard tile spacer arms and bead head.  I added a smaller bead for his mouth given his head is sort of gorilla shaped.  The paper was tough for him but once I got started doing it in layers it worked out fine.  Very easy to paint as well.  His belt is just cut tile spacer material glued onto the body and painted to match his standard equipment.

Now we have Lando and Luke.  They are both standard milk bottle figure construction.  Lando was tricky though because I had to paint the fact before adding the mask, and that was very, very tricky.  I love his look, though, just like in the movie I think he has one of the best armor configurations in the movie.  Luke was not too tough, I had done a figure for an rpg that was holding a sword extended like this, so I knew how to get the effect.  You trim the inside of the tile spacer arm, not the outside, so that you can create a "bend" effect and have the hands meet together in front of the figure.  The lightsaber is obviously a toothpick painted with florescent paint.I had to give him a "tunic" top which has small shoulder pads and flaps that extend down below his belt. I just did it with paper.  Same for the high color of the jacket.  

Now onto some bad guys ...


These guys are not my favorite henchmen, I like the guys on the other skiff better, but I do like the guy in the middle.  He's got it out for Luke because Luke killed this guy's pet rancor.  All three of these guys are standard milk bottle figure construction, nothing new really.


Melee guy and the pilot/blaster wielding guy.  They both turned out good, but nothing new construction wise.


Both skiffs together.  Now onto the sarlacc in its pit!


7 comments:

  1. Great to see you back with these wonderful figures. I do like the leaning into his shot as a pose. All in all terrific!
    Alan Tradgardland

    ReplyDelete
    Replies
    1. Thanks Alan. It's been fun to actually do figures that everyone is familiar with what they are "supposed" to look like. I might make a post about my "process" for how I go about trying to do that.

      Delete
  2. I'll say it before anyone else does (and take the opprobrium); henchman on the left could be a Ninja Turtle . . . there's a free idea! Love these and the previous post!

    H

    ReplyDelete
    Replies
    1. Indeed! In terms of comic book type figures, I do have some unpainted figures that I've made including Batman, Robin, the Joker, the Riddler, and the Penguin. I will eventually get around to them I hope, but the TMNT idea is a good one too! And this figure could be their skinny cousin!

      Delete
  3. Really outstanding representation of the characters. On the odd-looking blades, are they paper or wood?

    ReplyDelete
    Replies
    1. They are wood and tile spacers. I made a post about them just to answer your question more fully.

      Delete

Contributors

Followers

Blog Archive

Popular Posts

Labels I Use in Posts